Main and rod bearing oil clearance as the factory service manuals print it, with the crank journal sizes, crankshaft end play and rod side clearance. A large-journal small-block Chevy's rod clearance is 0.0013-0.0035 in. Where a manual gives a different figure for one journal, it is listed by journal number (#1 is the front).
These are factory figures for a stock rebuild. Performance builds usually run a little looser, about .00075" to .001" per inch of journal diameter; the bearing clearance calculator works that out from your own journal and bore measurements.
Work in progress. We are still filling these tables in from factory manuals and parts makers' catalogs, and a dash means we have not confirmed that figure from two sources yet. Have a figure we are missing, or see one that is wrong? Suggest an edit
| Engine | Figures from | Main bearing clearance (in) | Rod bearing clearance (in) |
|---|---|---|---|
| Small-block Chevy (Gen I, large journal) | 1968-up large journal | #1: 0.0008-0.0020; #2-4: 0.0011-0.0023; #5: 0.0017-0.0032 | 0.0013-0.0035 |
| Small-block Chevy 400 (Gen I) | 1970-80 | #1: 0.0008-0.0020; #2-4: 0.0011-0.0023; #5: 0.0017-0.0032 | 0.0013-0.0035 |
| Small-block Chevy (Gen II LT1/LT4) | 1994 Corvette manual (Gen II 1992-97) | #1: 0.0008-0.0020; #2-4: 0.0011-0.0020; #5: 0.0017-0.0032 | 0.0013-0.0035 |
| Small-block Chevy (Gen I, small journal) | 1955-1967 small journal | 1962 Corvette 327: 0.0008-0.0034; 1966 Chevelle 327: #1-4 0.0008-0.0034, #5 0.0010-0.0036; 1967 Corvette 327: #1 0.0008-0.0020, #2-4 0.0008-0.0024, #5 0.0015-0.0031 | 1962 Corvette 327: vertical 0.0007-0.0028, horizontal 0.0017-0.0038; 1966 Chevelle 327: 0.0007-0.0028; 1967 Corvette 327: 0.0007-0.0027 |
| Big-block Chevy (Mark IV) | 1978 (GM light truck manual) | #1-4: 0.0013-0.0025; #5: 0.0024-0.0040 | 0.0009-0.0025 |
| Big-block Chevy (Mark IV, 396/427 car) | 1965-1969 | 1966 Chevelle 396: #1-4 0.0006-0.0022 (printed '.006-.0022'), #5 0.0013-0.0029; 1967 Corvette 427 L36/L68: #1-2 0.0010-0.0022, #3-4 0.0013-0.0025, #5 0.0015-0.0031; 1967 Corvette 427 L71: #1-4 0.0013-0.0025, #5 0.0015-0.0031; 1969 Corvette 427 L36/L68: #1-2 0.0010-0.0020, #3-4 not legible, #5 0.0015-0.0031; 1969 Corvette 427 L71: #1-4 0.0013-0.0025, #5 0.0015-0.0031 | 1966 Chevelle 396: 0.0009-0.0025; 1967 Corvette 427 L36/L68: 0.0009-0.0029; 1967 Corvette 427 L71: 0.0014-0.0034 |
| LS (Gen III) | 1997-2004 Corvette set | 0.0008-0.0021 | 0.0009-0.0025 |
| LS (Gen IV) | 2006-2013 Holden VE workshop manual | 0.0008-0.0021 | 0.0009-0.0025 |
| Oldsmobile V8 (big block) | 1969 400 and 1970-71 455 (Oldsmobile 4-4-2 AMA specification forms) | #1-4: 0.0005-0.0021; 5 (rear): 0.0020-0.0034 | 0.0004-0.0033 |
| Buick V8 (1964: 300 and nailhead 401/425) | 1964 | 0.0005-0.0021 | 300: 0.0022 (as printed); 401/425: 0.0002-0.0023 |
| Buick V8 (350) | 1968-1980 | 0.0004-0.0015 | 1970-72 factory: 0.0002-0.0023; 1975: 0.0005-0.0026 |
| Buick V8 (400/430/455) | 1967-1976 | 0.0007-0.0018 | 1970-72 factory: 0.0002-0.0023; 1975: 0.0005-0.0026 |
| Ford small block (289/302/351W) | 1991 truck manual | 302 desired: #1 0.0001-0.0015, others 0.0005-0.0015; 302 allowable: #1 0.0001-0.0020, others 0.0005-0.0024; 351W desired: 0.0008-0.0015; 351W allowable: 0.0008-0.0026 | desired: 0.0008-0.0015; allowable 302: 0.0007-0.0024; allowable 351W: 0.0008-0.0025 |
| Ford 335 series (351M/400) | 1980 truck manual | desired: 0.0008-0.0015; allowable: 0.0008-0.0026 | desired: 0.0008-0.0015; allowable: 0.0008-0.0025 |
| Ford FE | 1973 truck manual | 360/390 desired: 0.0005-0.0015; 360/390 allowable: 0.0005-0.0025; 330, 361, 391 desired: 0.001-0.0015; 330, 361, 391 allowable: 0.001-0.0029 | 330/360/390 desired: 0.0008-0.0015; 330/360/390 allowable: 0.0008-0.0025; 361/391 desired: 0.001-0.0015; 361/391 allowable: 0.001-0.0029 |
| Ford 385 series (429/460) | 1991 truck manual | 1991 desired: 0.0008-0.0015; 1991 allowable: 0.0008-0.0026 | 1991 desired: 0.0008-0.0015; 1991 allowable: 0.0008-0.0025 |
| Ford Modular 4.6 (2V) | 1997 (Thunderbird/Cougar engine manual) and 1999-2004 (Mustang workshop manual) | 1997: 0.00106-0.00256; 1999-2004 desired: 0.001-0.002; 1999-2004 allowable: 0.00098-0.00197 | 0.00106-0.002717 (1999-2004: 0.0010629-0.0027165) |
| Ford Modular 5.4 / 5.8 | 2014 Mustang workshop manual | 0.0009-0.0019 | 0.001-0.0025 |
| Ford 5.0 Coyote | 2014 Mustang workshop manual | 2014 workshop manual: 0.0009-0.0018 | 2014 workshop manual: 0.0011-0.0027 |
| Ford 6.0 Power Stroke (International VT 365) | 2004-2006 International service manual EGES-295-2 | 0.0008-0.0034 | 0.0008-0.0033 |
| Mopar LA (318/340) | 1970 | desired: 0.0005-0.0015; allowed: 0.0025 | 318 desired: 0.0005-0.0015; 318 max: 0.0025; 340 desired: 0.0005-0.0020; 340 max: 0.003 |
| Mopar LA / Magnum (5.2 = 318, 5.9 = 360) | 1998 Ram | #1: 0.0005-0.0015; #2-5: 0.0005-0.002 | 0.0005-0.0022 |
| Mopar B/RB (383/440) | 1970 | desired: 0.0005-0.0015; allowed: 0.0025 | 440: 0.001-0.002; 383 2bbl: 0.0005-0.0015; 383 4bbl: 0.001-0.002; max: 0.0025 |
| Mopar 426 Hemi (Gen II) | 1970 | desired: 0.0015-0.0025; allowed: 0.0025 | desired: 0.0015-0.0025; max: 0.0025 |
| Mopar 5.7 Hemi (Gen III) | 2008 LX cars | 0.0009-0.002 | 0.0007-0.0023 |
| AMC V8 (Gen III 304/360/401) | 1981 Jeep | #1-4: 0.001-0.003 (0.0017-0.0020 preferred); 5 (rear): 0.002-0.004 (0.0025-0.003 preferred) | 0.001-0.003 (0.0020-0.0025 preferred) |
| AMC 258 inline six | 1981 Jeep | #1: 0.0005-0.0026 (0.0015 preferred); #2-6: 0.0005-0.003 (0.0017 preferred); #7: 0.0011-0.0035 (0.0023 preferred) | 0.001-0.0025 (0.0015-0.002 preferred) |
| AMC/Jeep 4.0 inline six | 1999 Wrangler (TJ) | 0.001-0.0025 (0.002 preferred) | 0.001-0.003 (0.0015-0.0020 preferred) |
| Cummins B 5.9 (6BT / ISB) | Cummins B Series shop manual (1991 & 1994 certification levels) | 0.0047 max | — |
| Honda B-series | 1994 and 1998 Acura Integra | #1,2,4,5: 0.0009-0.0017; #3: 0.0012-0.0019 | B18B1: 0.0008-0.0015; B18C1: 0.0013-0.0020; B18C5: 0.0015-0.0020 |
| Honda K-series | 2002 Acura RSX | #1,2,4,5: 0.0007-0.0016; #3: 0.0010-0.0019 | K20A3: 0.0008-0.0019; K20A2: 0.0013-0.0024 |
| Toyota JZ | 1997 Supra | 0.0010-0.0016 | 0.0009-0.0016 |
| Toyota 22R | 1983 Pickup service manual | 1983: 0.0006-0.0020; 22R-E: 0.0010-0.0022 | 1983: 0.0008-0.0020; 22R-E: 0.0010-0.0022 |
| Nissan RB26DETT | R32 (1989-94) engine manual | 0.028-0.047 (limit 0.090) mm | 0.020-0.040 (limit 0.090) mm |
| Nissan SR20 | 2002 Nissan Primera P11 electronic service manual (European) | 0.0002-0.0009, limit 0.0020 | 0.0008-0.0018, limit 0.00256 |
| Subaru EJ | 2010 Legacy/Outback service manual | 0.0004-0.0012 | 0.0006-0.0017 |
| Mitsubishi 4G63 | 1992-1993 Mitsubishi engine manuals | 0.0008-0.0020 | 0.0008-0.0020 |
Ford manuals print a desired range and a wider allowable (service) range. "Max" figures are the most clearance the manual allows on a used part.
| Engine | Main journal diameter (in) | Rod journal diameter (in) |
|---|---|---|
| Small-block Chevy (Gen I, large journal) | #1: 2.4484-2.4493; #2-4: 2.4481-2.4490; #5: 2.4479-2.4488 | 2.0988-2.0998 |
| Small-block Chevy 400 (Gen I) | #1-4: 2.6484-2.6493; #5: 2.6479-2.6488 | 2.0988-2.0998 |
| Small-block Chevy (Gen II LT1/LT4) | #1: 2.4484-2.4493; #2-4: 2.4481-2.4490; #5: 2.4479-2.4488 | 2.0978-2.0998 |
| Small-block Chevy (Gen I, small journal) | 1962 Corvette 327 (all mains, nominal): 2.2983 | 1.999-2.000 |
| Big-block Chevy (Mark IV) | #1: 2.7485-2.7494; #2-4: 2.7481-2.7490; #5: 2.7478-2.7488 | 2.1985-2.1995 |
| Big-block Chevy (Mark IV, 396/427 car) | — | 2.199-2.200 |
| LS (Gen III) | 2.558-2.559 | 2.0991-2.0999 |
| LS (Gen IV) | 2.558-2.559 | 2.0991-2.0999 |
| Oldsmobile V8 (big block) | AMA 1969-71 (nominal): 3.00; Motor 1969-75: 2.9993-3.0003 | 2.4988-2.4998 |
| Buick V8 (1964: 300 and nailhead 401/425) | 300: 2.2992; 401/425: 2.2495 | 300: 2.000; 401/425: 2.2495 |
| Buick V8 (350) | 2.9995 | 2.0000 |
| Buick V8 (400/430/455) | 3.2500 | 2.249-2.250 |
| Ford small block (289/302/351W) | 302: 2.2482-2.2490; 351W: 2.9994-3.0002 | 302: 2.1228-2.1236; 351W: 2.3103-2.3111 |
| Ford 335 series (351M/400) | 2.9994-3.0002 | 2.3103-2.3111 |
| Ford FE | 360/390: 2.7484-2.7492; 330 HD/361/391: 2.7479-2.7487 | 360/390: 2.4380-2.4388; 330 HD/361/391: 2.4377-2.4385 |
| Ford 385 series (429/460) | 2.9994-3.0002 | 2.4992-2.5000 |
| Ford Modular 4.6 (2V) | — | 1997: 2.08614-2.08673; 1999-2004: 2.085941-2.086728 |
| Ford Modular 5.4 / 5.8 | 2.6567-2.6577 | 2.0859-2.0867 |
| Ford 5.0 Coyote | 2.657-2.658 | 2.086-2.087 |
| Ford 6.0 Power Stroke (International VT 365) | 3.1885-3.1895 (converted; manual prints '3.188 to 3.150 in') | 2.716-2.717 |
| Mopar LA (318/340) | 2.4995-2.5005 | 2.124-2.125 |
| Mopar LA / Magnum (5.2 = 318, 5.9 = 360) | 5.2: 2.4995-2.5005; 5.9: 2.8095-2.8105 | 2.124-2.125 |
| Mopar B/RB (383/440) | 383: 2.6245-2.6255; 440: 2.7495-2.7505 | 2.374-2.375 |
| Mopar 426 Hemi (Gen II) | 2.7495-2.7505 | 2.374-2.375 |
| Mopar 5.7 Hemi (Gen III) | 2.5585-2.5595 | 2.125-2.126 |
| AMC V8 (Gen III 304/360/401) | #1-4: 2.7474-2.7489; rear (5): 2.7464-2.7479 | 2.0934-2.0955 |
| AMC 258 inline six | 2.4986-2.5001 | 2.0934-2.0955 |
| AMC/Jeep 4.0 inline six | #1-6: 2.4996-2.5001; #7: 2.4980-2.4995 | 2.0934-2.0955 |
| Honda B-series | #1,2,4,5: 2.1644-2.1654; 3 B18B1: 2.1642-2.1651; 3 B18C1: 2.1643-2.1653 | 1.7707-1.7717 |
| Honda K-series | 1,2,4,5 K20A3: 2.1648-2.1657; 1,2,4,5 K20A2: 2.1646-2.1655; 3 K20A3: 2.1644-2.1654; 3 K20A2: 2.1644-2.1652 | K20A3: 1.7707-1.7717; K20A2: 1.8888-1.8898 |
| Toyota JZ | 2.4403-2.4409 | 2.0465-2.0472 |
| Toyota 22R | 1983: 2.3614-2.3622; 22R-E: 2.3616-2.3622 | 1983: 2.0862-2.0866; 22R-E: 2.0861-2.0866 |
| Nissan RB26DETT | 54.951-54.975 mm | 47.961-47.974 mm |
| Nissan SR20 | 2.1636-2.1646 | 1.8880-1.8887 |
| Subaru EJ | 2.3619-2.3625 | 2.0466-2.0472 |
| Mitsubishi 4G63 | 2.2433-2.2441 | 1.7709-1.7717 |
Standard size. Undersize bearings are sold for cranks ground .010", .020" and .030" under these figures.
| Engine | Crankshaft end play (in) | Rod side clearance (in) |
|---|---|---|
| Small-block Chevy (Gen I, large journal) | 0.002-0.006 | 1978 truck manual: 0.008-0.014; 1987 Corvette manual: 0.006-0.014 |
| Small-block Chevy 400 (Gen I) | 0.002-0.006 | 0.008-0.014 |
| Small-block Chevy (Gen II LT1/LT4) | 0.001-0.007 | 0.006-0.014 |
| Small-block Chevy (Gen I, small journal) | 1962 Corvette: 0.002-0.006; 1966 Chevelle 327: 0.002-0.006; 1967 Corvette (one cell across the 327 and 427 columns): 0.006-0.010 | 1962 Corvette 327: 0.008-0.014; 1966 Chevelle 327: 0.009-0.013; 1967 Corvette 327: 0.009-0.013 |
| Big-block Chevy (Mark IV) | 0.006-0.010 | 0.013-0.023 |
| Big-block Chevy (Mark IV, 396/427 car) | 0.006-0.010 | 0.016-0.020 |
| LS (Gen III) | 0.0015-0.0078 | 0.00433-0.02 |
| LS (Gen IV) | 0.0015-0.0078 | 0.00433-0.02 |
| Oldsmobile V8 (big block) | 0.004-0.008 | 1969 400 (AMA): 0.002-0.011 (2 rods per crankpin); 1970-71 455 (AMA): 0.002-0.013 (2 rods per crankpin) |
| Buick V8 (1964: 300 and nailhead 401/425) | 0.004-0.008 | 0.005-0.012 total, both rods |
| Buick V8 (350) | 0.003-0.009 | 0.006-0.014 (total for both rods) |
| Buick V8 (400/430/455) | 0.003-0.009 | 0.005-0.012 (total for both rods) |
| Ford small block (289/302/351W) | 0.004-0.008 (service limit 0.012) | 0.010-0.020 (service limit 0.023) |
| Ford 335 series (351M/400) | 0.004-0.008 (service limit 0.012) | 0.010-0.020 (service limit 0.023) |
| Ford FE | 0.004-0.010 (wear limit 0.014) | as printed: 0.010-0.020; 360 & 390 (as printed): 0.008-0.025; wear limit: 0.030 |
| Ford 385 series (429/460) | 0.004-0.008 (service limit 0.012) | 0.010-0.020 (service limit 0.023) |
| Ford Modular 4.6 (2V) | 1997: 0.00519-0.011851; 1999-2004: 0.003-0.015 | 1997: 0.00059-0.01772 as printed; 1999-2004: 0.005-0.019 (service 0.01969) |
| Ford Modular 5.4 / 5.8 | 0.003-0.0148 | 0.0118 +/- 0.0069, max 0.0187 |
| Ford 5.0 Coyote | 2014 workshop manual (maximum): 0.011 | 2014 workshop manual: 0.0128 standard, 0.0197 max |
| Ford 6.0 Power Stroke (International VT 365) | 0.0087 max | 0.012-0.024 |
| Mopar LA (318/340) | 0.002-0.007 (max 0.010) | 0.006-0.014 (two rods) |
| Mopar LA / Magnum (5.2 = 318, 5.9 = 360) | 0.002-0.007 (service 0.010) | 0.006-0.014 |
| Mopar B/RB (383/440) | 0.002-0.007 (max 0.010) | 0.009-0.017 (two rods) |
| Mopar 426 Hemi (Gen II) | 0.002-0.007 (max 0.010) | 0.009-0.017 (two rods) |
| Mopar 5.7 Hemi (Gen III) | 0.002-0.011 (max 0.011) | — |
| AMC V8 (Gen III 304/360/401) | 0.003-0.008 | 0.006-0.018 |
| AMC 258 inline six | 0.0015-0.0065 | 0.010-0.019 |
| AMC/Jeep 4.0 inline six | 0.0015-0.0065 | 0.010-0.019 |
| Cummins B 5.9 (6BT / ISB) | 0.004-0.017 | 0.004-0.012 |
| Honda B-series | 0.004-0.014 | 0.006-0.012 |
| Honda K-series | 0.004-0.014 | 0.006-0.012 |
| Toyota JZ | 0.0008-0.0087 | 0.0098-0.0158 |
| Toyota 22R | 0.0008-0.0087 | 22R-E: 0.0063-0.0102 |
| Nissan RB26DETT | 0.05-0.18 (limit 0.3) mm | 0.2-0.3 (limit 0.4) mm |
| Nissan SR20 | 0.0039-0.0102, limit 0.0118 | 0.0079-0.0138, limit 0.020 |
| Subaru EJ | 0.0012-0.0045 | 0.0028-0.0130 |
| Mitsubishi 4G63 | 1993 (7-bolt): 0.0020-0.0098; 1992 (6-bolt): 0.0020-0.0071 | 0.0039-0.0098 |
Rod side clearance is for the pair of rods on one crank pin on V engines.
Measure the journal with a micrometer and the installed bearing with a bore gauge set to it, with the caps torqued to spec; the difference is the clearance. Plastigage gives a quick check of an assembled engine but reads only to about .0005".
A dash means the manuals we have do not print that figure for the engine, or the figure has not been confirmed yet.