The airflow an engine pulls at its peak-power rpm, from CFM = cubic inches × rpm × VE ÷ 3,456. A 350 that peaks at 5,500 rpm with bolt-ons (85% VE) moves about 475 cfm.
Read it as engine airflow, not the carb to buy: the street carbs makers list for a 350 run 600–750 cfm, because they size at or above the engine's airflow, never below it. The carburetor CFM calculator starts from these numbers and rounds up to a real carb size for your use.
| Cubic inches | 4,500 rpm | 5,000 rpm | 5,500 rpm | 6,000 rpm | 6,500 rpm | 7,000 rpm |
|---|---|---|---|---|---|---|
| 250 | 275 | 305 | 340 | 370 | 400 | 430 |
| 283 | 315 | 350 | 385 | 420 | 450 | 485 |
| 302 | 335 | 370 | 410 | 445 | 485 | 520 |
| 305 | 340 | 375 | 415 | 450 | 490 | 525 |
| 327 | 360 | 400 | 440 | 485 | 525 | 565 |
| 350 | 385 | 430 | 475 | 515 | 560 | 605 |
| 383 | 425 | 470 | 520 | 565 | 610 | 660 |
| 400 | 445 | 490 | 540 | 590 | 640 | 690 |
| 427 | 475 | 525 | 580 | 630 | 685 | 735 |
| 454 | 500 | 560 | 615 | 670 | 725 | 780 |
| 496 | 550 | 610 | 670 | 730 | 795 | 855 |
| 540 | 600 | 665 | 730 | 795 | 865 | 930 |
| Cubic inches | 4,500 rpm | 5,000 rpm | 5,500 rpm | 6,000 rpm | 6,500 rpm | 7,000 rpm |
|---|---|---|---|---|---|---|
| 250 | 260 | 290 | 320 | 345 | 375 | 405 |
| 283 | 295 | 330 | 360 | 395 | 425 | 460 |
| 302 | 315 | 350 | 385 | 420 | 455 | 490 |
| 305 | 320 | 355 | 390 | 425 | 460 | 495 |
| 327 | 340 | 380 | 415 | 455 | 490 | 530 |
| 350 | 365 | 405 | 445 | 485 | 525 | 565 |
| 383 | 400 | 445 | 490 | 530 | 575 | 620 |
| 400 | 415 | 465 | 510 | 555 | 600 | 650 |
| 427 | 445 | 495 | 545 | 595 | 640 | 690 |
| 454 | 475 | 525 | 580 | 630 | 685 | 735 |
| 496 | 515 | 575 | 630 | 690 | 745 | 805 |
| 540 | 565 | 625 | 690 | 750 | 815 | 875 |
| Cubic inches | 4,500 rpm | 5,000 rpm | 5,500 rpm | 6,000 rpm | 6,500 rpm | 7,000 rpm |
|---|---|---|---|---|---|---|
| 250 | 310 | 345 | 380 | 410 | 445 | 480 |
| 283 | 350 | 390 | 430 | 465 | 505 | 545 |
| 302 | 375 | 415 | 455 | 500 | 540 | 580 |
| 305 | 375 | 420 | 460 | 505 | 545 | 585 |
| 327 | 405 | 450 | 495 | 540 | 585 | 630 |
| 350 | 435 | 480 | 530 | 575 | 625 | 675 |
| 383 | 475 | 525 | 580 | 630 | 685 | 735 |
| 400 | 495 | 550 | 605 | 660 | 715 | 770 |
| 427 | 530 | 585 | 645 | 705 | 765 | 820 |
| 454 | 560 | 625 | 685 | 750 | 810 | 875 |
| 496 | 615 | 680 | 750 | 820 | 885 | 955 |
| 540 | 670 | 740 | 815 | 890 | 965 | 1040 |
Use the rpm where the engine makes peak power, not redline or peak torque. Pick the VE table that matches the build: stock cast-iron heads and a factory intake sit near 75–80%, bolt-ons near 80–85%, good aftermarket heads with a matched cam near 85–90%, full race 90% and up.
A vacuum-secondary carb can go a size above the chart number with little penalty; a mechanical-secondary (double pumper) on a street car should stay closer to it.