Static compression ratio alone does not decide what octane an engine needs. The cam does too: the later the intake valve closes, the more of the charge is pushed back out before compression starts, and the lower the dynamic compression ratio (DCR). Head material matters next, because aluminum heads pull heat out of the chamber and tolerate about 1.1 points more dynamic compression on the same fuel.
The first chart gives the most dynamic compression each fuel allows. The second and third turn that into static compression ratio vs octane for a 350 small block with common cam sizes. For your own engine, the compression ratio calculator works out static and dynamic compression and the octane from your bore, stroke, rod, chamber, gasket and cam.
| Fuel (pump octane) | Iron heads: most DCR | Aluminum heads: most DCR | Cranking pressure, iron | Cranking pressure, aluminum |
|---|---|---|---|---|
| 87 | 7.60:1 | 8.70:1 | 153 psi | 182 psi |
| 89 | 7.90:1 | 9.00:1 | 161 psi | 191 psi |
| 91 | 8.15:1 | 9.35:1 | 168 psi | 200 psi |
| 93 | 8.45:1 | 9.70:1 | 176 psi | 210 psi |
| 100 (race fuel, or about E85 at 105) | 9.50:1 | 10.90:1 | 204 psi | 244 psi |
| 110 race fuel | 11.00:1 | 12.80:1 | 247 psi | 299 psi |
Our own estimate, ±0.5 on pump gas: a knock model fitted to 15 published pump-gas builds, the same limits the compression calculator uses. Sea level, about 32° total timing, a traditional chamber and no knock sensor. Cranking pressure is estimated from DCR at sea level, ±10%.
| Static CR | Stock-type 204° (IVC 49°) | Mild street 214° (IVC 52°) | Street 224° (IVC 55°) | Hot street 236° (IVC 59°) | Street/strip 248° (IVC 65°) | Race 260° (IVC 71°) |
|---|---|---|---|---|---|---|
| 8.5:1 | 87 | 87 | 87 | 87 | 87 | 87 |
| 9.0:1 | 90 | 89 | 88 | 87 | 87 | 87 |
| 9.5:1 | 93 | 92 | 91 | 90 | 87 | 87 |
| 10.0:1 | 96 | 95 | 94 | 93 | 90 | 87 |
| 10.5:1 | 99 | 98 | 97 | 95 | 93 | 90 |
| 11.0:1 | 102 | 101 | 100 | 98 | 96 | 93 |
| 11.5:1 | 105 | 104 | 103 | 101 | 98 | 95 |
| 12.0:1 | 108 | 107 | 105 | 104 | 101 | 98 |
| 12.5:1 | 110+ | 109 | 108 | 106 | 103 | 100 |
| 13.0:1 | 110+ | 110+ | 110+ | 109 | 106 | 102 |
Octane needed, rounded up. 350 small-block Chevy (4.00" bore, 3.48" stroke, 5.7" rod). Cams named by intake duration at .050" lift; IVC is the effective intake closing in degrees ABDC (the .050" closing + 15°) at the intake centerline shown below. "110+" means more than 110 octane race fuel.
| Static CR | Stock-type 204° (IVC 49°) | Mild street 214° (IVC 52°) | Street 224° (IVC 55°) | Hot street 236° (IVC 59°) | Street/strip 248° (IVC 65°) | Race 260° (IVC 71°) |
|---|---|---|---|---|---|---|
| 8.5:1 | 87 | 87 | 87 | 87 | 87 | 87 |
| 9.0:1 | 87 | 87 | 87 | 87 | 87 | 87 |
| 9.5:1 | 87 | 87 | 87 | 87 | 87 | 87 |
| 10.0:1 | 88 | 88 | 87 | 87 | 87 | 87 |
| 10.5:1 | 91 | 90 | 89 | 88 | 87 | 87 |
| 11.0:1 | 94 | 93 | 92 | 90 | 88 | 87 |
| 11.5:1 | 96 | 95 | 94 | 93 | 90 | 87 |
| 12.0:1 | 99 | 98 | 97 | 95 | 93 | 90 |
| 12.5:1 | 101 | 100 | 99 | 97 | 95 | 92 |
| 13.0:1 | 103 | 102 | 101 | 100 | 97 | 94 |
Same engine and cams with aluminum heads.
Cams used: stock-type 204° at .050" installed at 112° intake centerline; mild street 214° at .050" installed at 110° intake centerline; street 224° at .050" installed at 108° intake centerline; hot street 236° at .050" installed at 106° intake centerline; street/strip 248° at .050" installed at 106° intake centerline; race 260° at .050" installed at 106° intake centerline.
| Static CR | Stock-type 204° (IVC 49°) | Mild street 214° (IVC 52°) | Street 224° (IVC 55°) | Hot street 236° (IVC 59°) | Street/strip 248° (IVC 65°) | Race 260° (IVC 71°) |
|---|---|---|---|---|---|---|
| 8.5:1 | 7.54 | 7.42 | 7.29 | 7.11 | 6.81 | 6.49 |
| 9.0:1 | 7.98 | 7.85 | 7.71 | 7.52 | 7.20 | 6.86 |
| 9.5:1 | 8.41 | 8.28 | 8.13 | 7.92 | 7.59 | 7.23 |
| 10.0:1 | 8.85 | 8.70 | 8.55 | 8.33 | 7.98 | 7.59 |
| 10.5:1 | 9.28 | 9.13 | 8.97 | 8.74 | 8.36 | 7.96 |
| 11.0:1 | 9.72 | 9.56 | 9.39 | 9.15 | 8.75 | 8.32 |
| 11.5:1 | 10.16 | 9.99 | 9.81 | 9.55 | 9.14 | 8.69 |
| 12.0:1 | 10.59 | 10.42 | 10.23 | 9.96 | 9.53 | 9.06 |
| 12.5:1 | 11.03 | 10.84 | 10.65 | 10.37 | 9.92 | 9.42 |
| 13.0:1 | 11.47 | 11.27 | 11.07 | 10.78 | 10.30 | 9.79 |
Dynamic compression ratio for the 350 above. A longer stroke or a shorter rod raises DCR a little at the same cam; run your own numbers in the calculator.
It depends on the cam and heads. With a stock-type cam, about 8.5:1 with iron heads; with aluminum heads about 9.5:1, by the chart above. The limit is a dynamic compression of about 7.6:1 with iron heads and 8.7:1 with aluminum.
With iron heads, a dynamic compression of about 8.45:1; with aluminum heads about 9.70:1. On a 350 with a street cam (224° at .050") that is about 9.5:1 static with iron heads and 11.0:1 or more with aluminum.
A longer-duration cam closes the intake valve later, after the piston has started back up. Until the valve closes, the cylinder cannot build pressure, so the effective (dynamic) compression is lower than the static ratio. That is why a 10.5:1 engine with a big cam can run pump gas when the same ratio with a stock cam would knock.
No. Boost raises the cylinder pressure on top of the compression ratio, so boosted engines need lower compression or more octane. Use the boost and compression calculator for those.
Thinner air lowers cylinder pressure, so engines at altitude tolerate more compression on the same fuel than this sea-level chart shows. Hot intake air, too much timing and a lean mixture all work the other way.