What a stroker crank does to an LS: the strokes the crank makers catalog, the cubic inches each bore and stroke gives, and the piston compression height left in a 9.240" deck block. Combinations are listed by bore and stroke because some names ("415", "428") are used for two different builds.
For any bore and stroke not listed here, use the displacement calculator; for rod angle and side load, the rod ratio calculator.
| Name | Bore × stroke | Cubic inches | Rod | Compression height | Rod ratio |
|---|---|---|---|---|---|
| 5.3 + 4.000 crank at 3.800 | 3.800" × 4.000" | 362.9 | 6.125" | 1.115" | 1.53 |
| 383 LS | 3.905" × 4.000" | 383.2 | 6.125" | 1.115" | 1.53 |
| 395 LS | 3.905" × 4.125" | 395.2 | 6.125" | 1.053" | 1.49 |
| 403 LS | 4.005" × 4.000" | 403.1 | 6.125" | 1.115" | 1.53 |
| 408 LS | 4.030" × 4.000" | 408.2 | 6.125" | 1.115" | 1.53 |
| 415 LS | 4.065" × 4.000" | 415.3 | 6.125" | 1.115" | 1.53 |
| 416 LS | 4.070" × 4.000" | 416.3 | 6.125" | 1.115" | 1.53 |
| 421 LS | 4.030" × 4.125" | 420.9 | 6.125" | 1.053" | 1.49 |
| 427 LS7 | 4.125" × 4.000" | 427.6 | 6.067" | 1.173" | 1.52 |
| 428 | 4.065" × 4.125" | 428.3 | 6.125" | 1.053" | 1.49 |
| 429 / 430 | 4.070" × 4.125" | 429.3 | 6.125" | 1.053" | 1.49 |
| 454 LS | 4.185" × 4.125" | 453.9 | 6.125" | 1.053" | 1.49 |
Compression height = deck height − half the stroke − rod length, at the 9.240" production deck.
| Stroke | Rod lengths sold with it | Makers listing it | Notes |
|---|---|---|---|
| 3.622" | 6.098, 6.100, 6.125 | 6 | Stock stroke. |
| 3.900" | 6.098, 6.125 | 3 | None stated by makers. |
| 4.000" | 6.098, 6.125, 6.200 | 7 | Maker statements: Eagle min rod 6.125 for counterweight-to-piston clearance ("any shorter rod will require clearancing of the counterweight"); Eagle's billet center-counterweight 3.622/4.000 cranks "fit into a stock block without modification". |
| 4.100" | 6.098, 6.125 | 5 | JE (Jeff Smith): production sleeve length is short except LS7, so use caution with cranks longer than 4.100. |
| 4.125" | 6.098, 6.125 | 7 | Eagle and Lunati min rod 6.125; K1 6.098. |
| 4.250" | 6.098, 6.125, 6.200, 6.300, 6.350, 6.460 | 6 | Fit in a 9.240" production block is disputed (see notes) |
| Stroke | 6.098" rod | 6.125" rod | 6.200" rod | 6.300" rod |
|---|---|---|---|---|
| 3.622" | 1.331" | 1.304" | 1.229" | 1.129" |
| 3.800" | 1.242" | 1.215" | 1.140" | 1.040" |
| 3.900" | 1.192" | 1.165" | 1.090" | 0.990" * |
| 4.000" | 1.142" | 1.115" | 1.040" | 0.940" * |
| 4.100" | 1.092" | 1.065" | 0.990" * | 0.890" * |
| 4.125" | 1.080" | 1.053" | 0.978" * | 0.878" * |
| 4.250" | 1.017" | 0.990" * | 0.915" * | 0.815" * |
* under 1.000": pistons this short are hard to find and leave the pin in the oil ring.
| Block | Stock bore | Max overbore | Deck height | Stock stroke | Stock rod |
|---|---|---|---|---|---|
| 4.8 / 5.3 iron (Gen III/IV truck) | 3.780" | — | 9.240" | 3.267" (4.8), 3.622" (5.3) | 6.098" (5.3) |
| 5.3 aluminum (Gen III/IV) | 3.780" | — | 9.240" | 3.622" | 6.098" |
| 5.7 aluminum LS1 / LS6 | 3.898" | 3.908" | 9.240" | 3.622" | 6.098" |
| 6.0 iron (Gen III/IV truck) | 4.000" | 4.060" | 9.240" | 3.622" | 6.098" |
| 6.0 aluminum (Gen IV) | 4.000" | 4.030" | 9.240" | 3.622" | 6.098" |
| 6.2 aluminum (Gen IV) | 4.065" | — | 9.240" | 3.622" | 6.098" |
| 7.0 aluminum LS7 | 4.125" | 4.135" | 9.240" | 4.000" | — |
Max overbore is shown only where the published figures agree; cylinder wall thickness varies with core shift, so sonic-check a block before boring it big.