Chrysler's B engines (350, 361, 383, 400) and raised-block RB engines (413, 426 Wedge, 440) share a 4.80-inch bore spacing; the RB's taller deck carries the longer stroke. The Mopar big block figures below come from the crank and piston makers' catalogs and factory specs, shown only where two references agree.
For a Mopar big block bore and stroke not listed, use the displacement calculator; for rod angle and side load, the rod ratio calculator.
Work in progress. We are still filling these tables in from factory manuals and parts makers' catalogs, and a dash means we have not confirmed that figure from two sources yet. Have a figure we are missing, or see one that is wrong? Suggest an edit
| Combination | Bore × stroke | Cubic inches | Rod | Compression height | Rod ratio |
|---|---|---|---|---|---|
| 350 B stock | 4.063" × 3.375" | 350.0 | 6.358" | 1.935" | 1.88 |
| 361 stock | 4.125" × 3.375" | 360.8 | 6.358" | 1.935" | 1.88 |
| 383 B stock | 4.250" × 3.375" | 383.0 | 6.358" | 1.935" | 1.88 |
| 400 stock | 4.342" × 3.375" | 399.8 | 6.358" | 1.935" | 1.88 |
| 383 RB stock | 4.031" × 3.750" | 382.9 | 6.768" | 2.082" | 1.80 |
| 413 stock | 4.188" × 3.750" | 413.2 | 6.768" | 2.082" | 1.80 |
| 426 Wedge stock | 4.250" × 3.750" | 425.6 | 6.768" | 2.082" | 1.80 |
| 440 stock | 4.320" × 3.750" | 439.7 | 6.768" | 2.082" | 1.80 |
| 383 + 3.750 crank at .030 | 4.280" × 3.750" | 431.6 | 6.760" | 1.345" | 1.80 |
| 400 + 3.750 crank at .033 | 4.375" × 3.750" | 451.0 | 6.760" | 1.345" | 1.80 |
| 400 + 4.150 crank at .033 | 4.375" × 4.150" | 499.1 | 6.760" | 1.145" | 1.63 |
| 440 + .030 overbore | 4.350" × 3.750" | 445.9 | 6.760" | 2.090" | 1.80 |
| 440 + 4.150 crank at .030 | 4.350" × 4.150" | 493.4 | 6.760" | 1.890" | 1.63 |
| 440 + 4.250 crank, 7.100 rod at .030 | 4.350" × 4.250" | 505.3 | 7.100" | 1.500" | 1.67 |
| 440 + 4.375 crank, 7.100 rod at .030 | 4.350" × 4.375" | 520.2 | 7.100" | 1.438" | 1.62 |
| 440 + 4.500 crank, 7.100 rod at 4.375 | 4.375" × 4.500" | 541.2 | 7.100" | 1.375" | 1.58 |
Compression height = deck height − half the stroke − rod length.
| Stroke | Rod lengths sold with it |
|---|---|
| 3.375" | 6.358 |
| 3.750" | 6.760 |
| 4.150" | 6.760 |
| 3.750" | 6.768, 6.760 |
| 4.150" | 6.760, 6.800 |
| 4.250" | 6.760, 6.800, 7.100 |
| 4.375" | 7.100 |
| 4.500" | 6.760, 6.800, 7.100 |
| Stroke | 6.358" rod | 6.535" rod | 6.760" rod |
|---|---|---|---|
| 3.375" | 1.935" | 1.758" | 1.533" |
| 3.750" | 1.747" | 1.570" | 1.345" |
| 3.900" | 1.672" | 1.495" | 1.270" |
| 4.150" | 1.547" | 1.370" | 1.145" |
| 4.250" | 1.497" | 1.320" | 1.095" |
* very short piston: the pin bore runs into the oil ring groove, so few pistons are made this short.
| Stroke | 6.760" rod | 6.768" rod | 6.800" rod | 7.100" rod |
|---|---|---|---|---|
| 3.750" | 2.090" | 2.082" | 2.050" | 1.750" |
| 3.900" | 2.015" | 2.007" | 1.975" | 1.675" |
| 4.150" | 1.890" | 1.882" | 1.850" | 1.550" |
| 4.250" | 1.840" | 1.832" | 1.800" | 1.500" |
| 4.375" | 1.777" | 1.769" | 1.737" | 1.438" |
| 4.500" | 1.715" | 1.707" | 1.675" | 1.375" |
* very short piston: the pin bore runs into the oil ring groove, so few pistons are made this short.
| Block | Stock bore | Deck height | Stock stroke | Stock rod |
|---|---|---|---|---|
| B 350 (1958) | 4.063" | 9.980" | 3.375" | 6.358" |
| B 361 (1958-1977, truck after 1966) | 4.125" | 9.980" | 3.375" | 6.358" |
| B 383 (1959-1971) | 4.250" | 9.980" | 3.375" | 6.358" |
| B 400 (1972-1978) | 4.342" | 9.980" | 3.375" | 6.358" |
| RB 383 (1959-60 Chrysler only) | 4.031" | 10.725" | 3.750" | 6.768" |
| RB 413 (1959-1965 car, later truck) | 4.188" | 10.725" | 3.750" | 6.768" |
| RB 426 Wedge (1962-1965) | 4.250" | 10.725" | 3.750" | 6.768" |
| RB 440 (1966-1978 car, 1979 truck) | 4.320" | 10.725" | 3.750" | 6.768" |