From the 1955 265 through the 400 and the 1992-97 LT1/LT4, the small-block Chevy shares one bore spacing and a long list of interchangeable parts. The SBC figures below come from the crank and piston makers' catalogs and factory specs, shown only where two references agree.
For a SBC bore and stroke not listed, use the displacement calculator; for rod angle and side load, the rod ratio calculator.
Work in progress. We are still filling these tables in from factory manuals and parts makers' catalogs, and a dash means we have not confirmed that figure from two sources yet. Have a figure we are missing, or see one that is wrong? Suggest an edit
| Combination | Bore × stroke | Cubic inches | Rod | Compression height | Rod ratio |
|---|---|---|---|---|---|
| 350 +.030 | 4.030" × 3.480" | 355.1 | 5.700" | 1.585" | 1.64 |
| 350 block, 3.750 crank, +.030 | 4.030" × 3.750" | 382.7 | 5.700" | 1.450" | 1.52 |
| 383 with 6.000 rod | 4.030" × 3.750" | 382.7 | 6.000" | 1.150" | 1.60 |
| 350 block, 3.875 crank, +.030 | 4.030" × 3.875" | 395.4 | 6.000" | 1.088" | 1.55 |
| 400 block, 3.750 crank, +.030 | 4.155" × 3.750" | 406.8 | 5.700" | 1.450" | 1.52 |
| 400 block stock bore, 3.750 | 4.125" × 3.750" | 400.9 | 5.565" | 1.585" | 1.48 |
| 400 block, 3.875 crank, +.030 | 4.155" × 3.875" | 420.3 | 6.000" | 1.088" | 1.55 |
| 400 block, 4.000 crank, +.030 | 4.155" × 4.000" | 433.9 | 6.000" | 1.025" | 1.50 |
| 305 block, 400 crank | 3.766" × 3.750" | 334.2 | 5.565" | 1.585" | 1.48 |
Compression height = deck height − half the stroke − rod length.
| Stroke | Rod lengths sold with it |
|---|---|
| 3.000" | 5.700, 6.125 |
| 3.250" | 5.700, 6.000 |
| 3.480" | 5.700, 6.000 |
| 3.500" | 5.700, 6.000 |
| 3.562" | 5.700, 6.000 |
| 3.625" | 5.700, 5.750 |
| 3.750" | 5.565, 5.700, 5.850, 6.000 |
| 3.800" | 5.700, 5.850, 6.000 |
| 3.875" | 5.850, 6.000 |
| 4.000" | 6.000 |
| Stroke | 5.565" rod | 5.700" rod | 6.000" rod | 6.125" rod |
|---|---|---|---|---|
| 3.000" | 1.960" | 1.825" | 1.525" | 1.400" |
| 3.250" | 1.835" | 1.700" | 1.400" | 1.275" |
| 3.480" | 1.720" | 1.585" | 1.285" | 1.160" |
| 3.500" | 1.710" | 1.575" | 1.275" | 1.150" |
| 3.562" | 1.679" | 1.544" | 1.244" | 1.119" |
| 3.625" | 1.647" | 1.513" | 1.213" | 1.088" |
| 3.750" | 1.585" | 1.450" | 1.150" | 1.025" |
| 3.800" | 1.560" | 1.425" | 1.125" | 1.000" |
| 3.875" | 1.522" | 1.388" | 1.088" | 0.963" * |
| 4.000" | 1.460" | 1.325" | 1.025" | 0.900" * |
| 4.125" | 1.397" | 1.263" | 0.963" * | 0.838" * |
| 4.250" | 1.335" | 1.200" | 0.900" * | 0.775" * |
* very short piston: the pin bore runs into the oil ring groove, so few pistons are made this short.
| Block | Stock bore | Deck height | Stock stroke | Stock rod |
|---|---|---|---|---|
| 350 production block (1967-on, incl. 1970-72 4-bolt, 1986-on one-piece seal, LT1/L31) | 4.000" | 9.025" | 3.480" | 5.700" |
| 400 production block (1970-80, siamese bores, steam holes) | 4.125" | 9.025" | 3.750" | 5.565" |
| 305 block (1976-on, 3.736 bore) | 3.736" | 9.025" | 3.480" | 5.700" |
| 265 (1955-57) | 3.750" | 9.025" | 3.000" | 5.700" |
| 283 (1957-67) | 3.875" | 9.025" | 3.000" | 5.700" |
| 302 (1967-69 Z28) | 4.000" | 9.025" | 3.000" | 5.700" |
| 307 (1968-73) | 3.875" | 9.025" | 3.250" | 5.700" |
| 327 (1962-69) | 4.000" | 9.025" | 3.250" | 5.700" |
| 262 (1975-76) | 3.671" | 9.025" | 3.100" | 5.700" |
| 267 (1979-82) | 3.500" | 9.025" | 3.480" | 5.700" |