Most four-stroke motorcycles, dirt bikes, ATVs and side-by-sides with overhead cams set valve clearance with shims. As the valve face and seat wear, the valve sits higher in the head and the gap between the cam lobe and the bucket closes up. A valve that runs out of clearance stops sealing: hard starting, lost compression and, left long enough, a burned valve.
The formula
New Shim = Current Shim + (Measured Clearance − Target Clearance)
Target the middle of the spec in your service manual. A gap that's too big takes a thicker shim; a gap that's too small takes a thinner one. Example: spec 0.10–0.15 mm (target 0.125), measured 0.05 mm, current shim 1.80 mm: 1.80 + (0.05 − 0.125) = 1.725 mm, so a 1.725 shim in a 0.025 mm kit. Valves already inside the spec stay as they are.
Motorcycle valve shim chart
The formula worked out ahead of time for a 0.10–0.15 mm spec (target 0.125 mm) and a shim kit in 0.025 mm steps: find your measured gap down the left side and your current shim across the top, and read the new shim where they cross. "OK" means the valve is already in spec.
| Measured gap (mm) | 1.60 shim | 1.70 shim | 1.80 shim | 1.90 shim | 2.00 shim |
|---|---|---|---|---|---|
| 0.00 | 1.475 | 1.575 | 1.675 | 1.775 | 1.875 |
| 0.03 | 1.500 | 1.600 | 1.700 | 1.800 | 1.900 |
| 0.05 | 1.525 | 1.625 | 1.725 | 1.825 | 1.925 |
| 0.08 | 1.550 | 1.650 | 1.750 | 1.850 | 1.950 |
| 0.10 | OK | OK | OK | OK | OK |
| 0.13 | OK | OK | OK | OK | OK |
| 0.15 | OK | OK | OK | OK | OK |
| 0.18 | 1.650 | 1.750 | 1.850 | 1.950 | 2.050 |
| 0.20 | 1.675 | 1.775 | 1.875 | 1.975 | 2.075 |
| 0.25 | 1.725 | 1.825 | 1.925 | 2.025 | 2.125 |
| 0.30 | 1.775 | 1.875 | 1.975 | 2.075 | 2.175 |
Your bike's spec may differ, so check the service manual and enter your own numbers in the calculator above. The valve shim chart page also has a chart for 0.05 mm car shims.
Checking clearance on a bike
- Engine cold. Specs are for a cold engine. Let it sit overnight or for several hours.
- Piston at TDC on the compression stroke for the cylinder you're checking, so both cam lobes point away from their buckets. The manual shows the timing marks.
- Feeler gauge between the lobe's base circle and the bucket. The right blade slides through with a light drag. Write down every valve before changing anything.
- Multi-cylinder engines: follow the manual's crank rotation order so each cylinder is checked at its own TDC.
Changing a shim
Modern sportbikes and four-stroke motocross bikes are mostly shim-under-bucket: the shim sits under the bucket on the valve stem, so the cams come out to reach it. Line up the timing marks first, take the cam chain tensioner off, and keep the chain from dropping into the cases. Lift the bucket, pick the shim out with a magnet, and mic it. The size printed on a shim is often its thickness with the decimal dropped ("170" for 1.70 mm), but worn shims measure thinner, so trust the micrometer. After reassembly, turn the engine over by hand and recheck every clearance you changed.
Older bikes with shim-over-bucket valvetrains can swap shims with a bucket depressor tool and the cams in place. Rocker-arm engines with screw-and-locknut adjusters don't use shims; set those with a feeler gauge.
Titanium valves and intakes that keep closing up
Many four-stroke motocross and enduro bikes use titanium intake valves with a thin hard coating. Once the coating wears through, the valve face and seat wear quickly and the intake gap keeps closing. One reshim is normal maintenance. Needing thinner shims on the same intake again and again is the sign the valves and seats need attention, and a thinner shim only hides it for a while.
Swap before you buy
On a multi-valve head, the shim one valve needs is often sitting in another valve on the same engine. The calculator checks every pair and suggests swaps when both valves end up in spec, which can save a trip to the dealer for a single shim.
Questions people ask
Is the motorcycle shim formula different from a car's?
No. The math is the same for any shim-and-bucket engine. What differs is the shim steps (bike kits are usually 0.025 mm or 0.05 mm), the number of valves per cylinder, and the checking order on multi-cylinder engines, which is what this version of the calculator sets up.
How often should I check valve clearance?
Go by the interval in your service manual. Race-ridden four-stroke dirt bikes are checked far more often than street bikes, and any bike that gets harder to start hot or cold is worth checking early.