The cranking pressure a compression test should show depends on the cam as much as the compression ratio. The later the intake valve closes, the more mixture is pushed back out before the piston starts compressing, so a big cam reads lower on the gauge with the same pistons.
These are estimates for a healthy engine at sea level, from the dynamic compression ratio. For your own bore, stroke, rod, chamber and cam, use the compression ratio calculator, which works out cranking pressure with the rest.
| Static CR | Stock-type 204° | Mild street 214° | Street 224° | Hot street 236° | Street/strip 248° | Race 260° |
|---|---|---|---|---|---|---|
| 8.5:1 | 150 psi | 150 psi | 145 psi | 140 psi | 130 psi | 125 psi |
| 9.0:1 | 165 psi | 160 psi | 155 psi | 150 psi | 140 psi | 135 psi |
| 9.5:1 | 175 psi | 170 psi | 165 psi | 160 psi | 155 psi | 145 psi |
| 10.0:1 | 185 psi | 185 psi | 180 psi | 170 psi | 165 psi | 155 psi |
| 10.5:1 | 200 psi | 195 psi | 190 psi | 185 psi | 175 psi | 160 psi |
| 11.0:1 | 210 psi | 205 psi | 200 psi | 195 psi | 185 psi | 170 psi |
| 11.5:1 | 225 psi | 220 psi | 215 psi | 205 psi | 195 psi | 180 psi |
| 12.0:1 | 235 psi | 230 psi | 225 psi | 215 psi | 205 psi | 190 psi |
| 12.5:1 | 245 psi | 240 psi | 235 psi | 230 psi | 215 psi | 200 psi |
| 13.0:1 | 260 psi | 255 psi | 250 psi | 240 psi | 225 psi | 210 psi |
Nearest 5 psi, ±10%. 350 small-block Chevy (4.00" bore, 3.48" stroke, 5.7" rod), cams named by intake duration at .050" lift and installed on the intake centerlines used in the compression and octane chart. Warm engine, throttle wide open, all plugs out, sea level. Subtract about 3-4% for each 1,000 ft of altitude.
| Cranking pressure | Dynamic compression ratio |
|---|---|
| 100 psi | 5.54:1 |
| 110 psi | 5.94:1 |
| 120 psi | 6.33:1 |
| 130 psi | 6.72:1 |
| 140 psi | 7.11:1 |
| 150 psi | 7.49:1 |
| 160 psi | 7.87:1 |
| 170 psi | 8.24:1 |
| 180 psi | 8.61:1 |
| 190 psi | 8.98:1 |
| 200 psi | 9.34:1 |
| 210 psi | 9.70:1 |
| 220 psi | 10.06:1 |
The same estimate run backward. Dynamic, not static: a gauge reading cannot tell you the static ratio without knowing the cam.
The spread between cylinders tells more than the number itself. Ford shop manuals call for the lowest cylinder to read at least 75% of the highest; GM service manuals use 70%. Most builders want a fresh engine within about 10% from highest to lowest.
A low cylinder that comes up after a squirt of oil in the plug hole points to rings. One that stays low points to a valve or the head gasket, and two low cylinders side by side often mean a gasket leaking between them. A leak-down test pins it down.
Octane needed for each combination is in the compression ratio and octane chart.