How to Read Cam Specs (Cam Card Explained)

A cam card lists a handful of numbers: duration, lift, lobe separation and intake centerline. Each describes one thing about when and how far the valves open, and together they decide the engine's idle, vacuum, power band and how much compression it can run.

This guide goes through each spec using a real cam from the camshaft database, the COMP Cams 12-242-2 (Small Block Chevy, hydraulic flat tappet): 224°/230° duration at .050", 0.477"/0.480" lift, 110° lobe separation.

The specs on a cam card

SpecCOMP Cams 12-242-2What it means
Duration at .050"224° intake / 230° exhaustCrank degrees the lifter is raised more than .050". The one duration figure that compares fairly between brands.
Advertised durationon the maker's cardDuration at the maker's own checking height (often .004" to .020"). Always bigger than the .050" figure, and not comparable between brands.
Valve lift0.477" / 0.480"Lobe lift × rocker ratio, at the stock rocker ratio (1.5:1 here). With zero lash; a solid-lifter cam loses its lash from this.
Lobe lift0.318" / 0.320"How far the lobe raises the lifter. Valve lift divided by the rocker ratio.
Lobe separation angle (LSA)110°Cam degrees between the intake and exhaust lobe centers. Ground into the cam; it cannot be changed at installation.
Intake centerline (ICL)106° ATDC in this example (4° advanced; use the card's figure)Where the intake lobe peaks, in crank degrees after TDC. Set at installation; many cards specify a few degrees of advance.
Lifter typeHydraulic flat tappetHydraulic or solid, flat tappet or roller. The cam, lifters and springs must match.
RPM range1,600–5,800The maker's operating range for a typical engine; it moves with displacement, heads and compression.

Duration: advertised vs .050"

Duration is how long the valve is open, in crankshaft degrees. Because the lobe's opening and closing ramps are gradual, the figure depends on where you start counting. Makers quote advertised duration at a low lift of their choosing, so two cams with the same advertised number can be quite different. Duration at .050" lifter rise is measured the same way by everyone, which is why it is the number to compare.

More duration holds the valves open longer, which moves the power band up the rpm range and closes the intake later, lowering dynamic compression and idle vacuum. As a rough guide for a small-block V8, about 200–215° at .050" is a stock-type to mild street cam, 215–230° a street performance cam, and 230° and up is lumpy, needs converter stall and gear, and suits higher compression.

Lift and rocker ratio

Valve lift is the lobe lift multiplied by the rocker ratio. On the COMP Cams 12-242-2, 0.318" of intake lobe lift × 1.5 = 0.477" at the valve. A 1.6:1 rocker on the same cam gives 0.509". More lift needs springs that will not coil bind, retainer-to-seal clearance and enough piston-to-valve clearance; check them with the valve spring calculator and the piston-to-valve calculator.

Lobe separation angle and overlap

Lobe separation is the angle between the intake and exhaust lobe centers in cam degrees. With duration fixed, a tighter LSA (106–108°) gives more overlap: a choppier idle, less vacuum and a peakier power band. A wider LSA (112–114°) gives less overlap: a smoother idle, more vacuum for power brakes, and a broader torque curve; it also suits supercharged and turbocharged engines. Overlap is the period around top dead center when both valves are open; at .050" it is intake opening BTDC plus exhaust closing ATDC.

Intake centerline and advance

The intake centerline is where the intake lobe peaks, in crank degrees after TDC. A cam installed "straight up" has its intake centerline equal to its LSA; installing it at a smaller centerline advances it, which opens and closes everything earlier and moves torque lower in the rpm range. Retarding does the opposite. The COMP Cams 12-242-2 is shown installed at 106° in this example, 4° advanced; install a real cam where its card says. To check where a cam actually sits, degree it in: see how to degree a cam.

Valve events at .050"

From the duration, LSA and centerline you can work out the four valve events. Intake opens = intake duration ÷ 2 − ICL (BTDC); intake closes = ICL + intake duration ÷ 2 − 180 (ABDC). The exhaust centerline = 2 × LSA − ICL; exhaust opens = exhaust centerline + exhaust duration ÷ 2 − 180 (BBDC); exhaust closes = exhaust duration ÷ 2 − exhaust centerline (ATDC). A negative opening or closing figure means the event happens on the other side of TDC.

Event at .050"COMP Cams 12-242-2
Intake opens6° BTDC
Intake closes38° ABDC
Exhaust opens49° BBDC
Exhaust closes1° ATDC
Exhaust centerline114° BTDC
Overlap at .050"7°

Installed at 106° intake centerline. The intake closing point drives dynamic compression: the compression calculator uses it to work out the octane the engine needs.

The cam duration calculator works these out for any cam, and the cam timing chart lists the factory valve events for hundreds of production engines.

Which specs matter when choosing a cam

Frequently asked questions

What do the numbers on a cam mean?

Usually duration (in degrees, at .050" and advertised), valve lift (in inches, at a stated rocker ratio), lobe separation angle and intake centerline (in degrees). Duration and LSA set the timing of the valve events; lift sets how far the valves open.

What does 224/230 mean on a cam?

Intake and exhaust duration, usually at .050" lift: 224° intake and 230° exhaust. A cam with two different figures is a dual-pattern cam, typically with more exhaust duration.

What is a good lobe separation angle for the street?

About 110–114° for a street engine: enough overlap for a little idle character while keeping vacuum and a broad torque curve. Tighter angles are for light race cars with gearing and stall to match.

Is more lift or more duration better?

They do different jobs. More lift with the same duration adds airflow if the heads keep flowing at that lift, usually with little change in idle or power band. More duration moves the power band up and costs low-end torque and vacuum.

Related